Skip to content

Heating Repair in Walnut Creek, CA

Serving Walnut Creek and nearby cities. Tell us about the job and we’ll call you back to confirm the details.

Tell us what’s going on

Prefer to talk? (650) 668-0834

The short answer

ExpertFlow HVAC Repair Service repairs gas furnaces and heat pumps in homes throughout Walnut Creek, CA. We diagnose the cause, explain your options, and fix the problem. If replacement makes more sense, we explain how current Bay Area Air District rules affect your choices.

When the heat stops working in Walnut Creek, it often happens on the first cold evening of the season, after the system has sat unused since spring. ExpertFlow HVAC Repair Service repairs heating systems in homes across Walnut Creek, including ZIP codes 94595, 94596, 94597 and 94598. We travel from our base in Pleasanton, about 18 miles away, to work on gas furnaces, heat pumps, and the thermostats and ductwork that connect them. On every call, we find the actual cause, explain it in plain terms, and fix it so your home is warm again.

Heating problems we often find in Walnut Creek homes

Walnut Creek has a wide mix of homes. Some have older forced-air furnaces in the attic, garage or hall closet. Others have newer heat pumps or have replaced one system with another. Many problems show up after months of no use, when dust, a weak part or a dead thermostat battery finally causes a failure.

These are the symptoms homeowners call us about most often:

  • Furnace runs, but the air from the vents is cool or barely warm
  • Burners light briefly and then shut off
  • No response at all when the thermostat calls for heat
  • Clicking, banging, squealing or rattling from the furnace or air handler
  • Some rooms stay cold while others overheat
  • Heat pump blows cool air in heating mode or ices up outside
  • A burning or musty smell that doesn't fade after the first few minutes of a new season

What happens during a heating repair visit

We start by asking what you've noticed: when the problem began, what the system sounds like, and whether it fails every time or only now and then. Then we test the system in order. We check the thermostat and power supply first, followed by ignition, flame sensing, safety switches, the blower motor, airflow and filters, and, on heat pumps, the refrigerant circuit and the defrost controls.

Before we do any work, we tell you what we found and what the repair involves. If a part has to be ordered, we tell you so and help you plan around it. If we see a safety concern, such as a cracked heat exchanger or a venting problem, we explain it clearly and recommend you don't run the system until it's fixed.

Repair or replace: what the Air District rules mean for you

Walnut Creek is within the Bay Area Air District, so its appliance rules apply to your home. Under Rule 9-4, natural gas furnaces manufactured from 2029 on must meet a zero-NOx emission standard. In practice, that points homeowners toward heat pumps when they replace a furnace after that date.

The rules do not require you to replace equipment that still works. They apply only when an existing furnace or water heater fails or is replaced. A sound furnace that needs a repair can usually just be repaired. When a system is near the end of its life, we'll explain the tradeoffs so you're not caught off guard later.

If you're considering a heat pump, keep in mind that the federal 25C tax credit only covered systems placed in service before December 31, 2025. It is not available for new installations. You can still check BayREN and your local clean energy provider for current electrification incentives. Those programs change with each funding cycle, so we confirm what's currently offered before we discuss it with you.

Heat pump heating repair

As more Walnut Creek homes switch to heat pumps, we're seeing more heat pump repair calls. Common causes include low refrigerant from a leak, a failed reversing valve, a defrost control that lets the outdoor coil ice over, and a thermostat that isn't set up correctly for a heat pump. Often the fix is a single part or a settings change, not a new system.

Quick checks before you call

A few simple checks can sometimes get the heat back on, or at least help us diagnose the problem faster:

  • Make sure the thermostat is set to Heat and the setpoint is above room temperature
  • Replace the thermostat batteries if it has them
  • Check for a tripped breaker and confirm the furnace's service switch is on
  • Replace a filter that looks gray or clogged
  • Make sure supply vents and return grilles aren't blocked by furniture or rugs

Serving Walnut Creek and nearby communities

Besides Walnut Creek and the rest of Contra Costa County, we provide heating repair in Moraga, Danville, San Ramon, Dublin and San Leandro. If you're nearby and not sure whether we serve your street, contact us and we'll let you know.

More services in Walnut Creek

Related

What to expect

How a visit goes

  1. Diagnose First

    We test and inspect the system to find what's actually causing the problem, so you aren't paying to replace parts that were working fine.

  2. Explain Your Options

    You'll hear what we found and the realistic choices, whether that's a repair, a replacement, or simply keeping an eye on it, before we start any work.

  3. Fit the System to the House

    For new installations, we look at your home's layout, ductwork, and how you use each room so the equipment matches the space it has to heat and cool.

FAQ

Common questions

Do you repair both gas furnaces and heat pumps in Walnut Creek?

Yes. We diagnose and repair gas furnaces, heat pumps, air handlers, thermostats and the ductwork issues that affect heating performance.

Will the Bay Area Air District make me replace my working furnace?

No. The Air District's appliance rules don't require replacing working equipment. They apply only when an existing furnace or water heater fails or is replaced.

Can I still get the federal tax credit for a heat pump?

No. The federal 25C credit covered qualifying heat pumps placed in service before December 31, 2025, and it isn't available for new installations. Check BayREN and your local clean energy provider for current local incentives.

Why does my furnace start and then shut off after a few seconds?

Common causes include a dirty flame sensor, a clogged filter that trips a safety limit, or a venting problem. We test each one to find the actual cause.

Is a burning smell normal when I turn the heat on?

A light dusty smell that fades within a few minutes on the first run of the season is usually dust burning off. If the smell is strong, lasts, or smells electrical, turn the system off and call us.

Which Walnut Creek ZIP codes do you serve?

We serve all of Walnut Creek, including 94595, 94596, 94597 and 94598, along with nearby Moraga, Danville, San Ramon, Dublin and San Leandro.

Need Heating or Cooling Help?

Tell us what's going on with your system, and we'll set up a visit to find the cause and walk you through your options.

Call (650) 668-0834 Request Service